Assumptions:
Assumptions I have made are that you have a Mastr II which operates properly, you have your crystals and they are mounted in the ICOMs.
International Crystal Manufacturing is a good source for Mastr II crystals but there are other sources like JAN and BOMAR.

ICOMs
ICOM's are Integrated Circuit Oscillator Modules, house the crystal used in the Mastr II radio.  The come in three versions, 2C, 5C and a EC.  EC ICOMs are designed to work with 5C's.  You should have one 5C installed which can temperature compensate many EC ICOMs.  The 2C ICOM can not temperature compensate an EC.
Here is a comprehensive description of the GE Mastr II ICOM's

Mastr II crystal frequency calculations
The IF frequency for both the UHF and VHF M2 is 11.2 MHz, CF equals the crystal frequency.

UHF Receiver - ((cf * 9) * 3) + IF = Receive frequency.
UHF Transmitter - (cf * 12) = Transmit frequency (PA has a tripler.)
VHF Receiver - (cf * 9) + IF = Receive frequency.
VHF Transmitter (cf * 12 ) = Transmit frequency.

Powering  Concerns:
Since the Mastr II was designed to be used in either a positive or negative ground vehicle, the A- is NOT connected to the chassis ground, but it is desired to strap them together when building a repeater.  This is explained below.

There are several power leads for the Mastr II.  There are the large RED lead that powers up the PA (TX A+), then is the A+ (16 Ga yellow) and IGN SWITCH (red).  All of those need +13.8 Volts DC.
Then there are the grounds:  The large BLACK wire (TX A-) and the A- (16 ga black), these can all be tied together.

If you don't have voltage connected to all of the points necessary (common when you don't use a control head and cable) the radio won't operate correctly or at all.

If you are either using a control cable or not, you need to insure all of the voltages and grounds are being supplied as connecting voltage to the two large terminals only supplies power to the Transmitter PA, again, as the radio was designed to operate either positive or negative ground and the chassis is not connected to A- (power ground), but it needs to be.  Also, A+ needs supplied to the IGN lead and A+ lead as this supplies voltage to the rest of the radios circuitry.

Install a 3 to 5 amp fuse in a holder from the large red wire to both the IGN and A+.  Then install a wire from the large black lead to both A- pins.

Refer here for the pin assignments to get the radio powered up.

Volume/Squelch Controls:
There are several ways to do this.
1) You can use the control head and cable as it was intended from the factory.
2) You can remove the pots from a surplus head and install them inside the radio by drilling the plastic wall between the compartments and wiring them directly.
3) Use the NHRC Vol/Sq pots.  This is the easy way out, and cheap too...

GE Channel Guard

CTCSS, Channel Guard, or PL... (what ever you want to call it)
The GE Channel Guard boards will not work as a full duplex encoder/decoder.  I use the Communications Specialists TS-32 or TS-64 encoder - decoder.

If the Mastr II you have had/has a GE Channel Guard (CTCSS, PL) board installed, or you can not get the transmitter to fire up (the transmit relay does not click) your radio may have been equipped with GE's Channel Guard board.  Removing the Channel Guard board has likely broken the PTT path.  You can check this simply by plugging the CG board back in place to see if the PTT path is restored.

Systems Boards
There are at least two different types of Systems Boards.  Look at the Systems board, to the left you will see the exciter connector, just below that you will see a 9 pin connector referred to as P908, just below this connector and below the right 3 pins of the this 9 pin connector you may see the image pictured with the Delta symbol.  If you see the Delta (triangle), you will see a solder pad to either side of the symbol.  To get your transmitter to work with out GE's Channel Guard board, you'll need to have a jumper installed on these solder pads.  If your radio has a Specialty Systems Board, it won't have the Delta symbol and thus pins 6 and 8 on P908 either need jumped or you can pick-up the PTT connection at pin 8 on P908.  Remember P908 is the 9 pin connector on the Systems Board that mates with the CG board, (the one in front of the exciter board).

Desense
Desense is an issue that is sometimes difficult to deal with because of the unknowns.  Any desense at all will degrade the receivers sensitivity.  The more critical 2 meter repeater (600 kHz split) has 10 db of quieting with a .32 uV. signal while the transmitter is wide open (160 watts).  The coax connecting the original antenna port (which will become the transmitter port when building a repeater) is not double shielded.  It should be replaced with RG-142, RG-400 or similar coax.  Use RG-142 or RG-400 for the interconnections from both the PA and receiver to the front panel of the chassis.  Use a "hood" to insure the connections are 100% shielded at connectors.

Of course, always use double shielded cable in you installation.  I use RG-214 for the transmitter and receiver signal path from the radio set to the duplexer.  If you are going to use a pre-amp, wire it in as close to the duplexer as possible.  This will eliminate any amplification of noise that may have found it's way in to the coax.

CAS and RUS
CAS stands for Carrier Activity Sensor.  It will go to around 10 volts (active high) when the receiver is un-squelched, but this pin produces a choppy representation of logic when a user is in flutter.  RUS should be used for COR to the controller. If you are using the factory Channel Guard board for tone decode in a Mastr II, you cannot use CAS, you need to use RUS anyway.  If in tone decode mode using the factory CG board, only the audio is muted. The CAS (or COS as some refer to it as) will still go high without the tone.  RUS line will go high only if the tone is decoded.  RUS line is not on the front connector. It is found on the audio/squelch board pins next to the CAS.  RUS is the RX squelch logic signal and stands for Receiver Unsquelched Sensor and is available at J904-8.